TweetFollow Us on Twitter

A MacMini Robot

Volume Number: 21 (2005)
Issue Number: 9
Column Tag: Programming

A MacMini Robot

Building A Vision Capable Robot Using A MacMini Computer

by Andrew Turner

Introduction

ADHOC/MacHack

For twenty years, the ADHOC/MacHack Conference has been gathering together groups of developers and Apple users to push a Macintosh computer to the limits. Along with the standard conference events of speakers, sessions, banquets, and meetings, there is the infamous Showcase. For 48 hours straight, Mac developers scurry to bend, twist, and otherwise manipulate the Apple Operating System and machines to perform unseen before tricks and feats. This may include the recently popularized MegaMan effect, which recreates stars streaming across your screen when you launch an app, reminiscent of the video game of the same name, or being able to replace your 'kernel-panic' splash screen. Whatever, the hack may be it's sure to be a lofty goal and, if the programmer is up to the challenge, very impressive.

Our goal was to take the Apple hardware outside of its usual desktop location and put it on a mobile platform and into the world.


Figure 1.

The Goal: a Mac powered robot

George Storm came to ADHOC with a mission in mind. The goal was to develop a Mac-powered robot. More than just a moving box, this robot would be remotely controllable, and autonomous navigation with vision capabilities. The result was a small, but impressive display of what modern Apple, and Mac related hardware can be combined to do.

The bTop Robot is a battery-powered, wheeled chassis centered around an Apple Mac mini computer. George had built the chassis system at his office in Washington over the past 6-months. Input from the outside world is obtained via a USB hardware interface board, a firewire iSight camera, and remote desktop for user driving. Software onboard the Mini allows a user to directly drive the robot, or activate a vision mode. In vision mode, the robot will use the iSight camera to track bright green objects. For our showcase demonstration, we wrapped bright green gaffer's tape around George's ankle. As he walked down the aisle to the center stage, the robot followed along like an obedient puppy.

The rest of the article explains the various components that comprise the bTop Robot as well as our experiences with developing software for the robot in our 48-hour development frenzy. Lastly, some overall experiences and targets for future development on the platform are presented.

Hardware Interface

The bTop Robot, like any physical robot, is a large combination of hardware components which are interfaced and driven via software in an onboard computer. Each of the sensors are senses that are fed to the central computer, or brain. Subsequently, the brain drives various motors for moving itself about in the world.

The Brain

The central processing unit of the bTop Robot is a Mac mini. Using an Apple Mini as the onboard processor allows for incredible power usually not found in embedded systems. The mini provides a full on-system development environment, easy network access, and a large array of input/output options.

To facilitate easier switching of power between a wall-unit and the onboard battery system the mini's power cable was cut and replaced with a simple BNC type twist lock connector. During long development, the mini was plugged into wall power and the entire chassis propped up to allow the powered wheels to spin freely. For testing and operation, the mini's power adapter was plugged into an onboard battery pack, which lasted up to 4 hours during minimal use and expected 45 minutes during heavy usage.

While working on the computer, a monitor, keyboard, and mouse were plugged in. This allowed for a very quick development cycle as the full Xcode compiler and debugger could be run on the targeted hardware. When testing was performed, the power adapter was switched to the onboard battery and the remote desktop application Timbuktu was used to operate the computer which had mild user interface lag and numerous problems with restricted ports on the hotel's wireless network. VNC would also have been a good choice for a remote desktop and may have presented fewer problems with network ports.

bTop-1 controller board

While the Mini is an amazingly powerful controller for a robot, it lacks decent low-level hardware device input and output. Historically, hardware developers would use a serial port or parallel port for easy interfacing with a computer. Modern USB and Firewire ports don't afford such convenience.

Fortunately, Perfectly Scientific (http://perfsci.com/) has developed a hardware I/O board specifically targeted to operate on the Mac platform. The bTop-1 board interfaces to the computer via a USB 2.0 connector and provides the following hardware ports:

  • 8 Analog-Digital (A/D) inputs (12-bit, 0~5V)
  • 8 Digital-Analog (D/A) outputs (8-bit, 0~2.56V)
  • 16 Digital Input/Output ports (0~5V input, 0~3.3V output)

The board connections are rows of double-row header pins. Also, there is a convenient screw-terminal block that can be used for tying in quick connects from other components. It is a good idea to connect via wire each of the I/O ports to a separate board with other electronics for each removal of the bTop-1 board.

The bTop Robot has an electronics tray above the MacMini computer and the bTop board mounted vertically alongside the mini computer. Connections from the bTop board to the electronics tray are done using a 16-pin ribbon cable that allowed easy connecting and disconnecting. The channels on the electronics tray were then split up to the appropriate subsystems.

George Storm has developed a comprehensive Objective-C API that allows for easy interfacing to the board's ports within Cocoa applications. The API and example applications are available on Perfectly Scientific's website. The following code snippet illustrates how to initialize the board, set the output of the digital and analog output ports. It is important to note that the analog output is 12-bit, and therefore uses decimal values 0~4095 (0~212-1) to corresponding voltages 0~5 Volts.


Figure 2.

// Set our bTop board level observer to this object
[bTopBoard setBTopBoardObserver:self];

// Set direction of Digital I/O port B to all outputs
[bTopBoard setPortBit:'B' direction:1];

// Set A/D ports 0 and 1 to 2 Volts and 5 Volts, respectively
[bTopBoard setADOut:0 value:1638];	
[bTopBoard setADOut:1 value:4095];

// Send a refresh for the board to perform all switching	
[bTopBoard refreshADPortValues];
[bTopBoard refreshDigitalPortValues]; 

Reading from the board is performed by instantiating an expected observer function. An observer is set using the setBTopBoardObserver function illustrated above. The observer function receives the analog input values as an array parameter which can be iterated through and the values extracted. Like the analog output values, these input values are encoded at 8-bits, and therefore vary from 0~255 (0~28-1) over 0~2.56 Volts:

- (void)bTop:(BTopBoard *)board receiveADData:(UInt16[8])values
{
   UInt8 count;
   UInt8 i;
	
   for(count = 0; count < 8; count++)
   {
      for(i=0;i<NUM_DISTANCE_SENSORS;++i)
      {
         if(count == m_distanceSensorAddress[i])
            m_distanceSensor[i] = values[count] / 255;
			
      }
   }
   [distanceRadarView setRadarLengths:m_distanceSensor];
}

Overall, the bTop board was an incredibly easy device to use for interfacing the Mac computer with external sensors. There was little complication on reading and controlling all of our sensors and actuators from a simple Objective-C API.

During development, we cross-connected several of the analog outputs with the analog inputs and the same with the digital inputs and outputs. Then as we exercised the virtual motors we observed the response on the expected sensor ports. After initial debugging, we connected the electronics tray into the bTop board and ran more tests on the actual robot.

Drivetrain

The bTop Robot is driven by a set of independently powered motors on chain drives to 5-inch diameter knobbed tire wheels. There is a small third caster wheel mounted on the back of the bTop Robot for stability.

Each wheel is made reversible by use of a simple switching circuit that is controlled through a bTop board digital I/O port. After choosing forward or backward, a 0~5 volt signal is sent to the motor to drive. Experience taught us that the motors need at least 1V of threshold power to begin turning. Furthermore, when testing we propped the robot on various objects to let the wheels spin freely. With no pressure on the drivetrain the motors tended to chatter. This chatter didn't actually occur in driving tests.

Sensors

Our desire was to have a Mac robot with multiple sensory inputs in addition to the very powerful iSight vision input. On hand we had several IR distance sensors, a line-following sensor, and accelerometer.

The accelerometer is a sensor that measures the local acceleration in a single axis. This is useful for obtaining a granular measure of pitch or roll of a body or the take-off acceleration of a moving vehicle. The bTop Robot is fairly slow in speed and low to the ground and exhibits minimal body pitch or roll and small accelerations. We therefore chose to not use the accelerometer onboard.

The distance sensors have dual LEDs in a single package. One LED sends out an infrared signal that is then measured by the other LED from reflected surfaces in front of the sensor. The output is a voltage which corresponds to the distance to the reflecting object. The bTop Robot has 6 of these sensor, 3 on the front bumper spaced 30 degrees apart, and 3 on the rear bumper spaced 30 degrees apart.

Lastly, we were also hoping to have bTop perform some line-following maneuvers. Using sensors similar to the distance sensors the LEDs would track on either side of a line. If the robot, and by consequence the sensors, crossed the line the sensor would indicate this. The robot's logic would then be able to turn according to the activated LED and get the robot back on line.

Due to time constraints of the 48-hour hack marathon before the final showcase, we were unable to implement this functionality. The hardware exists on the chassis and only awaits integration with the software to assist in driving the bTop Robot.



Figure 3.

Vision

Our primary, and lofty, goal of a vision controlled robot was realized through the power of a full onboard computer and firewire camera. The result was a vision system that could identify, locate, and communicate the position of brightly colored objects. Due to available materials, we chose a neon green gaffer's tape as our target color for the vision system to track.

Looking for colors

Each year the ADHOC/MacHack showcase demonstrates some great techniques for performing tasks on a Mac. Sometimes the original developer or new developers build upon previous years' inspiration and codebase. Last year, Lisa Lippincott developed a hack called 'ScrollPlate', which was designed to compensate for the lack of a scroll wheel on a powerbook laptop. Using the iSight camera and a paper plate with a red up-arrow on one side, and a green down-arrow on the other side, the program would control a window's scroll bar. When the use showed the red up-arrow, the window would scroll up. Consequently, when the user showed the iSight camera the green down-arrow, the window would scroll down. Another ingenious, but mostly pointless hack, well done.

ScrollPlate's source code already solved many of the problems we would have integrating vision onboard the bTop Robot. The largest hurdle, we found out, was integrating the processor intensive Carbon code into the Cocoa robot controller application and still leave the computer enough processing time to drive the motors.

ScrollPlate itself was built upon modifications to an Apple demonstration application that would identify lobsters on the iSight camera. Our first modification was to identify the color we wanted to track. Using a photograph of the gaffers tape and an eye-dropper tool we obtained RGB values for the specific green. Then, we converted these values to YUV, which is an easier parameter set in which to allow for ranges corresponding to light and dark variations of the green tape depending on external lighting.

Telling where the color is

After we determined the color, and range of variations in color, we were looking for, we had to determine where this color was in the frame, and then where this color was in the world.

After some 'precise' measurements, via large pieces of paper and a ruler, we determined the iSight had a field of view of 33-inches wide at 42-inches away. A conversion function allowed us to convert a location in the pixel coordinates of the vision frame to an approximate angle (radians) in the real world.

static double PixelToAngle(int pixel, int pixelFieldWidth)
{
   /* We measured 33 inches wide at 42 inches away */
   double fieldWidth = 33.0 / 42.0;   
   return atan( ( (double)pixel - pixelFieldWidth/2.0 ) / pixelFieldWidth * fieldWidth );
}

After the pixel center and bounding box was determined in angles, these values were sent to the robot controller, which determined appropriate driving behavior.

There was some difficulty with the vision system when there was insufficient lighting on the tracked object, or when various other green objects showed up in the camera's sight. For example, the robot once began to veer wildly away in testing. After some investigation we found the leftover roll of gaffers tape left on a box about 15 feet away that the robot began heading towards.

Semi-Autonomous Control System

User-controlled driving

For testing and general mayhem, we implemented a driver-in-the-loop controller for allowing remote operators to drive the bTop Robot around. The robot is like a tank, with two parallel wheels that operate in tandem to drive forward, turn, or reverse the chassis. In order to make driving easy and natural for an untrained operator, a simple point-and-click interface was designed.

Since the project was under a time-crunch, and for easy development, an onboard user interface was developed that was controlled through the Timbuktu remote desktop. A custom interface for controls and sensors was developed using the CustomView box in Interface Builder and constructing the interface using Quartz commands. We decided building up a custom interface was a better solution that attempting to modify a common control to display information meaningfully.


Figure 4.

A user clicks and drags in the steering circle to operate the robot. Dragging forward and to the left or right drives the robot forward with simple turning by slowing down the wheel on the inside of the turn. For example, to make a left turn, the right wheel is slowed down. The same effect happens when the user drags down in the steering circle, but in reverse.

Since the robot has two wheels mounted almost across the center of gravity of the robot, spin maneuvers are possible. By clicking and dragging horizontally to the left or right of the steering circle the robot will perform an in-place spin maneuver.

For safety, and ease of operation, when the user releases the mouse button the robot is sent a stop command and the steering circle is reset. One easter egg related to development did leave a type of 'cruise-control'. If the user clicked, and dragged within the steering circle and kept dragging the mouse point out of the circle and then releasing, the robot would be sent the same command and continue one its way. By simply single-clicking within the steering circle the robot would be sent a stop command and come to rest.

The user interface also displayed the output of the front and rear distance sensors to the robot. The triangle bars correspond to distance and change from green, to yellow, to red as the obstructive object gets closer to the robot.

Vision-controlled driving

The button on the bottom left of the user interface invokes the vision control. Due to the high processing power, limit of the frame rate of the desktop through Timbuktu and perhaps other elements, it was not possible to control the robot via the driving interface once the vision interface was invoked.


Figure 5.

The maximum bound of the green object as well as the average center of the bounds were then sent to the robot controller. Careful testing, performed sometime in the middle of the night, showed that the acceptable range of object width was up to 0.3 radians, or 17.2 degrees. Therefore, when the object took up more than this width of the image, then the robot would stop. In between a 0.3 radian width and down to a 0.05 radian width, the robot scaled its velocity linearly.

Robot heading was determined by the variation of the center of the target color. Between +/- 0.3 radians, the robot scaled its heading linearly as a percentage of the maximum range. Beyond the 0.3 radians width, when the object was either on the far left or right of the image, or even out of range, then the robot would stop and spin to face the target better.

After a heading and velocity were determined from the vision system, the commands were sent to the same low-level controller used by the human-based driving.

Robot in Motion

The ADHOC/MacHack showcase begins 48-hours after the conference opens, which is at midnight on Friday night. While showcase hacks should be complete before the beginning of the showcase, technically the hack isn't due until right before the end of the showcase. This ending time varies depending on the number of showcase entries.

Like any good software project we utilized all the time available to us, including the time well past the original deadline. Our development team was still writing and debugging the bTop Robot during the showcase presentations. In fact, the last bug of our software was due to a behavior of the Objective-C compiler, which causes only a warning, but not an error, when a C++ header file is missing and unknown C-functions are called. With several minutes to go this last bug was figured out and the bTop Robot finally tested.

As the last hack to demonstrate of the night the stage was set for our entrance. We dimmed all the lights, which also helped the vision system, and shown a single flashlight on the George Storm's ankle, where the gaffer tape was fastened, as he walked down the aisle. Scooting along behind, the bTop Robot made it's way down the aisle to the center stage.

The robot system performed excellently down a very complex row of chairs, bags, and other objects. It was even able to traverse several cables that lay across the aisle. The following night, at the awards banquet, the bTop Robot received 3rd place in the open-vote judging, earning its developers, and the Mac mobile platform, well deserved honors.

Future Work

The ADHOC/MacHack project putting together the bTop Robot was a terrific experience. Having a group of knowledgeable developers and technicians together willing to assist wherever possible was a great boon to putting the system together in such a short timeframe. However, due to the limiting time, there were many features that were left out and many corners that were cut in developing the vision and control system.

For the future, we would like to clean up the code that controls the robot and move the user interface to a remote computer running as a client connecting to the Mac mini as a server. This would limit the need of a remote desktop tool like Timbuktu or VNC for operating the robot.

There were several sensor systems that were not fully utilized such as the distance sensors and line-followers. Integrating these into the robot with some safety mechanisms ("Don't run into any objects"), as well as advanced control scenarios ("Follow this line", "Track along the wall") would be desired. There are also many other sensors that would easily integrate onto the chassis and connect through the bTop board. Perhaps implementing a plug-in architecture to the software would allow for easy adding and removing of hardware interface components.

Lastly, while the ScrollPlate software performed adequately for the hack demonstration, the frame rate was limited to 5FPS and modifications are difficult. It may be possible to implement a vision system using a Quartz Composer component in the cocoa application, or CoreImage to create a better solution. The bTop Robot could track different colors, light and dark areas, or individually shaped objects.

Resources

ADHOC/MacHack Conference: http://adhocconference.com

Perfectly Scientific - makers of the bTop-1 hardware board: http://perfsci.com

bTop Robot Yahoo! Group: http://groups.yahoo.com/group/bTop_Robot


Andrew Turner is a Systems Development Engineer with Realtime Technologies, Inc (http://www.simcreator.com) and has built robotic airships, automated his house, designed spacecraft, and in general looks for any excuse to hack together cool technology. You can read more about his projects at http://www.highearthorbit.com.

George Storm has been a Macintosh developer since six months after its release, primarily working in frameworks and GUI. Prior to his programming experience he worked for more than ten years in electronic R&D in a wide variety of disciplines and holds three patents for mechanical devices related to handicapped access.

Lisa Lippincott designs hot new internet technology, even now that it's unfashionable. Since 1996 she's been designing it at BigFix, finding ways to deliver information about computer problems to people who have problematic computers.

 

Community Search:
MacTech Search:

Software Updates via MacUpdate

Capture One 11.0.1.40 - RAW workflow sof...
Capture One is a professional RAW converter offering you ultimate image quality with accurate colors and incredible detail from more than 400 high-end cameras -- straight out of the box. It offers... Read more
GraphicConverter 10.5.4 - $39.95
GraphicConverter is an all-purpose image-editing program that can import 200 different graphic-based formats, edit the image, and export it to any of 80 available file formats. The high-end editing... Read more
Dash 4.1.3 - Instant search and offline...
Dash is an API documentation browser and code snippet manager. Dash helps you store snippets of code, as well as instantly search and browse documentation for almost any API you might use (for a full... Read more
Microsoft OneNote 16.9 - Free digital no...
OneNote is your very own digital notebook. With OneNote, you can capture that flash of genius, that moment of inspiration, or that list of errands that's too important to forget. Whether you're at... Read more
DEVONthink Pro 2.9.17 - Knowledge base,...
Save 10% with our exclusive coupon code: MACUPDATE10 DEVONthink Pro is your essential assistant for today's world, where almost everything is digital. From shopping receipts to important research... Read more
OmniGraffle 7.6 - Create diagrams, flow...
OmniGraffle helps you draw beautiful diagrams, family trees, flow charts, org charts, layouts, and (mathematically speaking) any other directed or non-directed graphs. We've had people use Graffle to... Read more
iFinance 4.3.7 - Comprehensively manage...
iFinance allows you to keep track of your income and spending -- from your lunchbreak coffee to your new car -- in the most convenient and fastest way. Clearly arranged transaction lists of all your... Read more
Opera 50.0.2762.58 - High-performance We...
Opera is a fast and secure browser trusted by millions of users. With the intuitive interface, Speed Dial and visual bookmarks for organizing favorite sites, news feature with fresh, relevant content... Read more
Microsoft Office 2016 16.9 - Popular pro...
Microsoft Office 2016 - Unmistakably Office, designed for Mac. The new versions of Word, Excel, PowerPoint, Outlook and OneNote provide the best of both worlds for Mac users - the familiar Office... Read more
SoftRAID 5.6.4 - High-quality RAID manag...
SoftRAID allows you to create and manage disk arrays to increase performance and reliability. SoftRAID allows the user to create and manage RAID 4 and 5 volumes, RAID 1+0, and RAID 1 (Mirror) and... Read more

Latest Forum Discussions

See All

Around the Empire: What have you missed...
Around this time every week we're going to have a look at the comings and goings on the other sites in Steel Media's pocket-gaming empire. We'll round up the very best content you might have missed, so you're always going to be up to date with the... | Read more »
The 7 best games that came out for iPhon...
Well, it's that time of the week. You know what I mean. You know exactly what I mean. It's the time of the week when we take a look at the best games that have landed on the App Store over the past seven days. And there are some real doozies here... | Read more »
Popular MMO Strategy game Lords Mobile i...
Delve into the crowded halls of the Play Store and you’ll find mobile fantasy strategy MMOs-a-plenty. One that’s kicking off the new year in style however is IGG’s Lords Mobile, which has beaten out the fierce competition to receive Google Play’s... | Read more »
Blocky Racing is a funky and fresh new k...
Blocky Racing has zoomed onto the App Store and Google Play this week, bringing with it plenty of classic kart racing shenanigans that will take you straight back to your childhood. If you’ve found yourself hooked on games like Mario Kart or Crash... | Read more »
Cytus II (Games)
Cytus II 1.0.1 Device: iOS Universal Category: Games Price: $1.99, Version: 1.0.1 (iTunes) Description: "Cytus II" is a music rhythm game created by Rayark Games. It's our fourth rhythm game title, following the footsteps of three... | Read more »
JYDGE (Games)
JYDGE 1.0.0 Device: iOS Universal Category: Games Price: $4.99, Version: 1.0.0 (iTunes) Description: Build your JYDGE. Enter Edenbyrg. Get out alive. JYDGE is a lawful but awful roguehate top-down shooter where you get to build your... | Read more »
Tako Bubble guide - Tips and Tricks to S...
Tako Bubble is a pretty simple and fun puzzler, but the game can get downright devious with its puzzle design. If you insist on not paying for the game and want to manage your lives appropriately, check out these tips so you can avoid getting... | Read more »
Everything about Hero Academy 2 - The co...
It's fair to say we've spent a good deal of time on Hero Academy 2. So much so, that we think we're probably in a really good place to give you some advice about how to get the most out of the game. And in this guide, that's exactly what you're... | Read more »
Everything about Hero Academy 2: Part 3...
In the third part of our Hero Academy 2 guide we're going to take a look at the different modes you can play in the game. We'll explain what you need to do in each of them, and tell you why it's important that you do. [Read more] | Read more »
Everything about Hero Academy 2: Part 2...
In this second part of our guide to Hero Academy 2, we're going to have a look at the different card types that you're going to be using in the game. We'll split them up into different sections too, to make sure you're getting the most information... | Read more »

Price Scanner via MacPrices.net

Deals on clearance 15″ Apple MacBook Pros wit...
B&H Photo has clearance 2016 15″ MacBook Pros available for up to $800 off original MSRP. Shipping is free, and B&H charges NY & NJ sales tax only: – 15″ 2.7GHz Touch Bar MacBook Pro... Read more
Apple restocked Certified Refurbished 13″ Mac...
Apple has restocked a full line of Certified Refurbished 2017 13″ MacBook Airs starting at $849. An Apple one-year warranty is included with each MacBook, and shipping is free: – 13″ 1.8GHz/8GB/128GB... Read more
How to find the lowest prices on 2017 Apple M...
Apple has Certified Refurbished 13″ and 15″ 2017 MacBook Pros available for $200 to $420 off the cost of new models. Apple’s refurbished prices are the lowest available for each model from any... Read more
The lowest prices anywhere on Apple 12″ MacBo...
Apple has Certified Refurbished 2017 12″ Retina MacBooks available for $200-$240 off the cost of new models. Apple will include a standard one-year warranty with each MacBook, and shipping is free.... Read more
Apple now offering a full line of Certified R...
Apple is now offering Certified Refurbished 2017 10″ and 12″ iPad Pros for $100-$190 off MSRP, depending on the model. An Apple one-year warranty is included with each model, and shipping is free: –... Read more
27″ iMacs on sale for $100-$130 off MSRP, pay...
B&H Photo has 27″ iMacs on sale for $100-$130 off MSRP. Shipping is free, and B&H charges sales tax for NY & NJ residents only: – 27″ 3.8GHz iMac (MNED2LL/A): $2199 $100 off MSRP – 27″ 3.... Read more
2.8GHz Mac mini on sale for $899, $100 off MS...
B&H Photo has the 2.8GHz Mac mini (model number MGEQ2LL/A) on sale for $899 including free shipping plus NY & NJ sales tax only. Their price is $100 off MSRP. Read more
Apple offers Certified Refurbished iPad minis...
Apple has Certified Refurbished 128GB iPad minis available today for $339 including free shipping. Apple’s standard one-year warranty is included. Their price is $60 off MSRP. Read more
Amazon offers 13″ 256GB MacBook Air for $1049...
Amazon has the 13″ 1.8GHz/256B #Apple #MacBook Air on sale today for $150 off MSRP including free shipping: – 13″ 1.8GHz/256GB MacBook Air (MQD42LL/A): $1049.99, $150 off MSRP Read more
9.7-inch 2017 WiFi iPads on sale starting at...
B&H Photo has 9.7″ 2017 WiFi #Apple #iPads on sale for $30 off MSRP for a limited time. Shipping is free, and pay sales tax in NY & NJ only: – 32GB iPad WiFi: $299, $30 off – 128GB iPad WiFi... Read more

Jobs Board

*Apple* Data Center Site Selection and Strat...
# Apple Data Center Site Selection and Strategy Research Analyst Job Number: 83708609 Santa Clara Valley, California, United States Posted: 18-Jan-2018 Weekly Hours: Read more
Security Engineering Coordinator, *Apple* R...
# Security Engineering Coordinator, Apple Retail Job Number: 113237456 Santa Clara Valley, California, United States Posted: 18-Jan-2018 Weekly Hours: 40.00 **Job Read more
Firmware Engineer - *Apple* Accessories - A...
# Firmware Engineer - Apple Accessories Job Number: 113422485 Santa Clara Valley, California, United States Posted: 18-Jan-2018 Weekly Hours: 40.00 **Job Summary** Read more
*Apple* Retail - Multiple Positions - Apple,...
Job Description: Sales Specialist - Retail Customer Service and Sales Transform Apple Store visitors into loyal Apple customers. When customers enter the store, Read more
*Apple* Store Leader - Retail District Manag...
Job Description:Job SummaryAs more and more people discover Apple , they visit our retail stores seeking ways to incorporate our products into their lives. It's your Read more
All contents are Copyright 1984-2011 by Xplain Corporation. All rights reserved. Theme designed by Icreon.