TweetFollow Us on Twitter

Serial Ports as Slots
Volume Number:1
Issue Number:8
Column Tag:The Electrical Mac

"Macintosh Serial Ports"

By Jeff Mitchell, President, Digital Solutions, MacTutor Contributing Editor

The Macintosh has frequently been criticized for its lack of hardware expansion capability. Apple's response has been that the two high-speed serial ports act as 'virtual slots' which give the user practically unlimited expansion capability. Although the merits of this approach may be debatable, it is nevertheless our only point of access to the internals of the Macintosh.

In this article, I will describe both the RS-232-C and the RS-422-A standards and examine their compatibility. I will then examine in detail Apple's implementation of RS-422 in the Macintosh serial ports and describe how to interface them with standard RS-232 peripherals, along with precautions to be taken in order to maintain data integrity and protect your equipment from damage.


Electronic Industries Association (EIA) Standard RS-232-C, Interface Between Data Terminal Equipment and Data Communication Equipment Employing Serial Binary Data Interchange, released in August 1969, defines how data terminal equipment (DTE) and data communication equipment (DCE) exchange information serially.

Originally, DTE was intended to be a dumb terminal, and DCE was intended to be a modem. The large number of handshake lines were included to provide control over what were entirely hardware driven devices, with no local intelligence. As microprocessors became popular and devices became capable of implementing handshaking protocols in software, many of the handshake lines became superfluous. This, combined with the popularity of using RS-232 to connect all types of different devices not even imagined at the time the standard was written, makes signal definition somewhat subjective and is what causes us so much grief when trying to make interconnecting cables.

EIA Standard RS-232-C defines electrical, mechanical, and signal characteristics. Electrically, a mark, or binary one, is defined as less than 3 volts with respect to signal ground, while a space, or binary zero, is greater than 3 volts. The region between +3 volts is defined as the transition region, where the signal state is not uniquely defined. The maximum open-circuit voltage is not to exceed +25 volts. In addition, there are some restrictions on source and load impedances, load capacitance, and slew rates.

Mechanically, the standard assigns signal definitions to 25 pins (including 3 unassigned pins), although no particular connector type is specified. However, the 25 pin subminiature-D type connector (DB-25) has emerged as a de-facto standard. Cable length is recommended to be kept to less than 50 feet, although the load capacitance of 2500 picofarads is really the limiting factor.

Signal characteristics are defined in some detail in the standard, although if not applied to a strict terminal/modem configuration, they tend to become open to interpretation. Data rates are restricted to a nominal 20,000 bits per second.

Standards notwithstanding, how is RS-232 generally implemented? Electrically, most equipment uses MC1488 (or equivalent) drivers operating from +12 volt supplies, and MC1489 (or equivalent) receivers operating from +5 volts. The drivers accept a standard TTL level in and convert it to about +10 volts out, inverting it in the process to meet the RS-232 mark/space requirements.

The receivers do not operate in strict accordance with RS-232, since their input switching threshold is around +1 volt. Therefore these receivers will correctly respond not only to RS-232 input levels, but TTL level inputs also. Like the drivers, the output is inverted from the input.

RS-422-A, RS-449

EIA Standard RS-422-A, Electrical Characteristics of Balanced Voltage Digital Interface Circuits, released in December 1978, defines the interchange of serial binary signals between DTE and DCE, or in any point-to-point interconnection of serial binary signals between digital equipment.

There are several significant differences between RS-232 and RS-422. Most importantly, RS-422 is a balanced interface. Secondly, note that this standard defines electrical characteristics only. EIA Standard RS-449 defines the mechanical and signal characteristics and will be included in this discussion. A final, more subtle point: notice that the description of the standard has been expanded to include connection of any digital equipment, not only DCE and DTE.

The RS-422 specification defines a balanced interface. This means that instead of a voltage on one signal line being referenced to a common ground, as in RS-232, the signal is carried on two lines which are always in complementary states (see Fig.1). The threshold criteria in a balanced system is the voltage difference between the two signals, not the absolute value of either with respect to ground. The open circuit voltage between the two outputs is not to exceed 6.0 volts, and cannot be less than 2.0 volts when driving a load of 100 + 1%. In addition, there are restrictions on offset voltages, short circuit output current, and receiver specifications, among others.

Mechanically, RS-449 defines a 37 pin and a 9 pin interface, where the 9 pin interface is defined as a secondary channel for the 37 pin interface. As with RS-232, signals are given pin assignments. Unlike RS-232, standard connectors are specified. In recognition of the de-facto DB-25 standard for RS-232, RS-449 defines DS-37 and DE-9 connectors (The D indicates subminiature-D type, the B, S, and E indicate shell size, and the 25, 37, and 9 are number of pins. Note that a DB-9 would be a DB-25 with 16 pins missing.). Maximum cable length using 24 AWG twisted pair cable varies according to signalling rate, from 50 feet at 10 Mbits/sec to 4000 feet at 100 Kbits/sec or less.

Signal characteristics are described in RS-449, again with the emphasis on a terminal/modem configuration. A table showing equivalent RS-232 signals is provided in the standard.

The industry standards for RS-422 drivers and receivers are the Am26LS31 (or equivalent) and the Am26LS32 (or equivalent), respectively. Both of these devices operate off a single +5 volt supply, and meet all the requirements set forth in the EIA standard.


As defined, how compatible is RS-422 with RS-232? During development of the RS-422 and RS-449 standards, the EIA gave close attention to an orderly transition from existing RS-232 equipment. For systems designed strictly to the letter of the standards, interoperability is assured. Realistically, most systems will be compatible electrically, but signal definitions and mechanical connections are another matter.

Remember, however, that RS-422 is differential, and the only relation it has to signal ground is that the midpoint of the output voltage swing must be within +3 volts of ground and the input to either receiver input terminal cannot exceed +10 volts with respect to ground. For systems operating off of standard supply voltages and using industry standard parts, this is not a problem. In addition, RS-422 does not meet the voltage swing requirement of RS-232, but generally suffices at the short cable lengths found in RS-232 installations. The specifics of how to interface a single-ended to a differential signal will be covered below.

Do you need to worry about damaging your Mac or peripherals while trying to connect a new piece of equipment? RS-232 specifies that drivers be able to withstand an open circuit, a short to any other signal line, or a short to ground without damage. Receivers must be able to withstand +25 volts without damage. A short between any two signal lines should not result in a current of more than 1/2 amp. RS-232, therefore, is essentially bulletproof.

RS-422 leaves fail-safe operation more to the system designer, but specifies that an output shorted to ground be limited to 150 mA and that receivers shall operate correctly over a common mode voltage of +7 volts and with a maximum differential voltage of 12 volts. These requirements result in a fail-safe system as long as it remains an RS-422 interface.

For a mixed RS-232/RS-422 system, there is a possibility of device damage since the maximum RS-232 voltage levels are +25 volts. The 26LS32 receivers have been designed to withstand this input voltage range, meaning that they can be connected to RS-232 drivers with relative impunity. RS-422 drivers can be damaged by shorting them to voltages above 5.5 volts or below ground (26LS31), or to voltages greater than +15 volts (26LS30). To summarize, RS-422 cannot damage RS-232, but RS-232 can damage RS-422 under some conditions.

Macintosh Serial Ports

In order for their concept of the 'virtual slot' to be accepted as a viable alternative to true hardware expandability, Apple had to forego the industry standard RS-232 in favor of an interface that would support a much higher data rate, thus the choice of RS-422. They also chose to compromise the standard somewhat in order to make the output voltages more compatible with RS-232.

For output drivers, the Macintosh uses 26LS30's running from +5 volt supplies, rather than the single +5 volt supply recommended by the manufacturer for RS-422 operation. The result is a symmetrical open-circuit voltage swing of about 8 volts centered around ground. This drops to about 4 volts when loaded with 100 . Centering the output signal around ground makes it RS-232 compatible, but the 8 volt open circuit voltage exceeds the RS-422 restriction of a maximum of 6 volts.

The receivers are 26LS32's and meet all RS-422 requirements. Since the Macintosh handshake line is a single-ended input, the inverting input on that receiver is tied to ground, making that input RS-232 compatible. The TXD and RXD lines are differential but are compatible with RS-232 levels when connected to the inverting (-) terminals. The 26LS32 is designed so the non-inverting (+) input floats at about +2.7 volts when open and the inverting input floats at about +1.8 volts. Therefore, when an RS-232 signal is connected to the inverting input the receiver will switch around +2.7 volts if the non-inverting input is left open, which is within the +3 volt RS-232 spec.

Between the drivers/receivers and the connectors, the signal lines go through an RC filter network. This is not part of the RS-422 specification, but is included to meet FCC EMI requirements and to provide signal deglitching.

The Macintosh serial connector pinout is as follows:



2 +5 V


4 TXD +

5 TXD -

6 +12 V


8 RXD +

9 RXD -

For RS-232 compatibility, use Gnd, TXD-, and RXD- (remember, RS-232 signals are inverted). The HSK line goes to both the CTS and the TRxC inputs on the 8530 chip in the Macintosh. Depending upon how the chip is configured by the serial driver, this line may be used as a handshake line or as an external clock in order to increase data transfer speeds. The +5 volt and +12 volt outputs come directly from the power supply inside the Macintosh. Apple warns that the +5 volt line may turn into an output handshake line at some future date and that it should not be used. They also warn that the +12 volt line is for detecting power only. When connecting peripherals or making cables, exercise caution, but you'll probably not be able to damage any of the interface circuitry. Pay special attention to the power pins (2 & 6), however, since these are tied directly to the power supply and are not protected from accidental shorting.

Electrically, like most of the Macintosh hardware, the serial ports are quite simple. Some compromises to the RS-422 standard were made in Apple's implementation, but generally speaking, these are not significant. The end result has been to provide users with a much more flexible interface, able to communicate with nearly all RS-232 peripherals in addition to supporting much higher data transfer rates for applications that require it, such as external disk drives and networking.


Community Search:
MacTech Search:

Software Updates via MacUpdate

Civilization VI 1.1.0 - Next iteration o...
Sid Meier’s Civilization VI is the next entry in the popular Civilization franchise. Originally created by legendary game designer Sid Meier, Civilization is a strategy game in which you attempt to... Read more
Network Radar 2.3.3 - $17.99
Network Radar is an advanced network scanning and managing tool. Featuring an easy-to-use and streamlined design, the all-new Network Radar 2 has been engineered from the ground up as a modern Mac... Read more
Printopia 3.0.8 - Share Mac printers wit...
Run Printopia on your Mac to share its printers to any capable iPhone, iPad, or iPod Touch. Printopia will also add virtual printers, allowing you to save print-outs to your Mac and send to apps.... Read more
ForkLift 3.2.1 - Powerful file manager:...
ForkLift is a powerful file manager and ferociously fast FTP client clothed in a clean and versatile UI that offers the combination of absolute simplicity and raw power expected from a well-executed... Read more
BetterTouchTool 2.417 - Customize multi-...
BetterTouchTool adds many new, fully customizable gestures to the Magic Mouse, Multi-Touch MacBook trackpad, and Magic Trackpad. These gestures are customizable: Magic Mouse: Pinch in / out (zoom... Read more
Little Snitch 4.0.6 - Alerts you about o...
Little Snitch gives you control over your private outgoing data. Track background activity As soon as your computer connects to the Internet, applications often have permission to send any... Read more
Google Chrome 65.0.3325.181 - Modern and...
Google Chrome is a Web browser by Google, created to be a modern platform for Web pages and applications. It utilizes very fast loading of Web pages and has a V8 engine, which is a custom built... Read more
TeamViewer 13.1.2991 - Establish remote...
TeamViewer gives you remote control of any computer or Mac over the Internet within seconds or can be used for online meetings. Find out why more than 200 million users trust TeamViewer! Free for non... Read more
Printopia 3.0.8 - Share Mac printers wit...
Run Printopia on your Mac to share its printers to any capable iPhone, iPad, or iPod Touch. Printopia will also add virtual printers, allowing you to save print-outs to your Mac and send to apps.... Read more
BetterTouchTool 2.417 - Customize multi-...
BetterTouchTool adds many new, fully customizable gestures to the Magic Mouse, Multi-Touch MacBook trackpad, and Magic Trackpad. These gestures are customizable: Magic Mouse: Pinch in / out (zoom... Read more

Latest Forum Discussions

See All

The best games that came out for iPhone...
It's not a huge surprise that there's not a massive influx of new, must-buy games on the App Store this week. After all, GDC is happening, so everyone's busy at parties and networking and dying from a sinister form of jetlag. That said, there are... | Read more »
Destiny meets its mobile match - Everyth...
Shadowgun Legends is the latest game in the Shadowgun series, and it's taking the franchise in some interesting new directions. Which is good news. The even better news is that it's coming out tomorrow, so if you didn't make it into the beta you... | Read more »
How PUBG, Fortnite, and the battle royal...
The history of the battle royale genre isn't a long one. While the nascent parts of the experience have existed ever since players first started killing one another online, it's really only in the past six years that the genre has coalesced into... | Read more »
Around the Empire: What have you missed...
Oh hi nice reader, and thanks for popping in to check out our weekly round-up of all the stuff that you might have missed across the Steel Media network. Yeah, that's right, it's a big ol' network. Obviously 148Apps is the best, but there are some... | Read more »
All the best games on sale for iPhone an...
It might not have been the greatest week for new releases on the App Store, but don't let that get you down, because there are some truly incredible games on sale for iPhone and iPad right now. Seriously, you could buy anything on this list and I... | Read more »
Everything You Need to Know About The Fo...
In just over a week, Epic Games has made a flurry of announcements. First, they revealed that Fortnite—their ultra-popular PUBG competitor—is coming to mobile. This was followed by brief sign-up period for interested beta testers before sending out... | Read more »
The best games that came out for iPhone...
It's not been the best week for games on the App Store. There are a few decent ones here and there, but nothing that's really going to make you throw down what you're doing and run to the nearest WiFi hotspot in order to download it. That's not to... | Read more »
Death Coming (Games)
Death Coming Device: iOS Universal Category: Games Price: $1.99, Version: (iTunes) Description: --- Background Story ---You Died. Pure and simple, but death was not the end. You have become an agent of Death: a... | Read more »
Hints, tips, and tricks for Empires and...
Empires and Puzzles is a slick match-stuff RPG that mixes in a bunch of city-building aspects to keep things fresh. And it's currently the Game of the Day over on the App Store. So, if you're picking it up for the first time today, we thought it'd... | Read more »
What You Need to Know About Sam Barlow’s...
Sam Barlow’s follow up to Her Story is #WarGames, an interactive video series that reimagines the 1983 film WarGames in a more present day context. It’s not exactly a game, but it’s definitely still interesting. Here are the top things you should... | Read more »

Price Scanner via

Thursday roundup of the best 13″ MacBook Pro...
B&H Photo has new 2017 13″ MacBook Pros on sale for up to $200 off MSRP. Shipping is free, and B&H charges sales tax for NY & NJ residents only. Their prices are the lowest available for... Read more
Sale: 9.7-inch 2017 WiFi iPads starting at $2...
B&H Photo has 9.7″ 2017 WiFi Apple iPads on sale for $40 off MSRP for a limited time. Shipping is free, and pay sales tax in NY & NJ only: – 32GB iPad WiFi: $289, $40 off – 128GB iPad WiFi: $... Read more
Roundup of Certified Refurbished iPads, iPad...
Apple has Certified Refurbished 9.7″ WiFi iPads available for $50-$80 off the cost of new models. An Apple one-year warranty is included with each iPad, and shipping is free: – 9″ 32GB WiFi iPad: $... Read more
Back in stock! Apple’s full line of Certified...
Save $300-$300 on the purchase of a 2017 13″ MacBook Pro today with Certified Refurbished models at Apple. Apple’s refurbished prices are the lowest available for each model from any reseller. A... Read more
Wednesday deals: Huge sale on Apple 15″ MacBo...
Adorama has new 2017 15″ MacBook Pros on sale for $250-$300 off MSRP. Shipping is free, and Adorama charges sales tax in NJ and NY only: – 15″ 2.8GHz Touch Bar MacBook Pro Space Gray (MPTR2LL/A): $... Read more
Apple offers Certified Refurbished Series 3 A...
Apple has Certified Refurbished Series 3 Apple Watch GPS models available for $50, or 13%, off the cost of new models. Apple’s standard 1-year warranty is included, and shipping is free. Numerous... Read more
12″ 1.2GHz Space Gray MacBook on sale for $11...
B&H Photo has the Space Gray 12″ 1.2GHz MacBook on sale for $100 off MSRP. Shipping is free, and B&H charges sales tax for NY & NJ residents only: – 12″ 1.2GHz Space Gray MacBook: $1199 $... Read more
Mac minis available for up to $150 off MSRP w...
Apple has restocked Certified Refurbished Mac minis starting at $419. Apple’s one-year warranty is included with each mini, and shipping is free: – 1.4GHz Mac mini: $419 $80 off MSRP – 2.6GHz Mac... Read more
Back in stock: 13-inch 2.5GHz MacBook Pro (Ce...
Apple has Certified Refurbished 13″ 2.5GHz MacBook Pros (MD101LL/A) available for $829, or $270 off original MSRP. Apple’s one-year warranty is standard, and shipping is free: – 13″ 2.5GHz MacBook... Read more
Apple restocks Certified Refurbished 2017 13″...
Apple has Certified Refurbished 2017 13″ MacBook Airs available starting at $849. An Apple one-year warranty is included with each MacBook, and shipping is free: – 13″ 1.8GHz/8GB/128GB MacBook Air (... Read more

Jobs Board

Payments Counsel - *Apple* Pay (payments, c...
# Payments Counsel - Apple Pay (payments, credit/debit) Job Number: 112941729 Santa Clara Valley, California, United States Posted: 26-Feb-2018 Weekly Hours: 40.00 Read more
Firmware Engineer - *Apple* Accessories - A...
# Firmware Engineer - Apple Accessories Job Number: 113452350 Santa Clara Valley, California, United States Posted: 28-Feb-2018 Weekly Hours: 40.00 **Job Summary** Read more
*Apple* Solutions Consultant - Apple (United...
# Apple Solutions Consultant Job Number: 113501424 Norman, Oklahoma, United States Posted: 15-Feb-2018 Weekly Hours: 40.00 **Job Summary** Are you passionate about Read more
*Apple* Inc. Is Look For *Apple* Genius Te...
Apple Inc. Is Look For Apple Genius Technical Customer Service Minneapolis Mn In Minneapolis - Apple , Inc. Apple Genius Technical Customer Service Read more
*Apple* Genius Technical Customer Service Co...
Apple Genius Technical Customer Service Columbus Oh Apple Inc. - Apple , Inc. Apple Genius Technical Customer Service Columbus Oh - Apple , Inc. Job Read more
All contents are Copyright 1984-2011 by Xplain Corporation. All rights reserved. Theme designed by Icreon.